Flat roof
Are bituminous roofing membranes resistant to road salt?- Can a vapour barrier be installed on a concrete surface that is not air-dry yet?
- Can an existing bituminous roof structure be renovated with IKO Atelia?
- Can IKO Hybritech MS Detail be applied to an IKO bituminous roofing membrane?
- Can IKO liquid waterproofing be applied to a specific substrate?
- Can IKO metatech Detail be applied on an IKO bituminous roofing membrane?
- Can IKO offer a liquid product mixed according to the customer’s formula? Does IKO provide tolling services?
- Can waterproofing be fully bonded to an IKO enertherm PIR insulation board?
- Do IKO bituminous roofing membranes contain asbestos?
- Does FM approval take Broof values into account?
- How are stains from bituminous coatings best removed from a hard surface?
- How can a building owner submit a request for an IKO Atelia circular roof?
- How can a pitched roof be insulated with IKO Enertherm?
- How can I properly maintain my bituminous roof?
- How can stains from a bituminous primer be removed?
- How can the lifespan of my bituminous roof covering be extended using roof coatings?
- How can you optimize rainwater harvesting on a flat roof?
- How is a base layer torched onto a bitumen-faced PIR insulation board (IKO enertherm BM)?
- How is a bituminous cap sheet applied with mechanical fasteners?
- How is a bituminous membrane applied using bituminous cold adhesive?
- How is a bituminous underlayer mechanically fastened?
- How is a bituminous waterproofing membrane installed on a rough or uneven concrete surface?
- How is an expansion joint properly constructed with bituminous roofing membranes on a flat roof?
- How is IKO liquid waterproofing applied?
- How is the limit for mineral loss on a bituminous roofing membrane determined?
- How is the thermal performance of an insulation material expressed?
- How is the wind uplift resistance of a bituminous roofing system with self-adhesive Quadra underlayer on IKO Enertherm ALU insulation ensured?
- How Many Fixings Are Needed Per IKO Enertherm PIR Insulation Board for Mechanical Fixation?
- How many screws are used to fasten an IKO Enertherm PIR insulation board on a flat roof?
- How should IKO Enertherm PIR insulation boards be installed on rofiled teel sheets?
- How to bond insulation boards on a flat roof?
- How to connect a bituminous membrane to a lead roof outlet?
- How to install a two-layer bituminous waterproofing system with a partially self-adhesive base layer on PIR ALU insulation?
- How to torch-weld a bituminous cap sheet on a flat roof
- Is a PE vapour barrier sufficient in a flat roof build-up on a cementitious substrate?
- Is PIR insulation suitable for insulating foundations?
- To what thickness can an IKO enertherm PIR insulation board be bonded in a warm roof construction in accordance with ATG?
- Warm, Cold, or Inverted Flat Roof: What’s the Difference?
- What aesthetic finishes does IKO offer for liquid waterproofing systems on balconies?
- What are the advantages of quadra profiles compared to stripe profiles in a vapour pressure distributing bituminous membrane?
- What are the causes and dangers of algae formation on a flat roof?
- What are the cost differences between mechanically fastened and adhered systems?
- What are the key considerations when applying a bituminous cap sheet?
- What are the possible causes of craquelé/crater formation after applying a solvent-based bituminous coating?
- What does an IKO roof detail look like?
- What drainage systems are available for flat roofs?
- What is the advantage to use polypropylene tapes around bituminous roofing membranes?
- What is the difference between IKO hybritech MS Detail and IKO hybritech Detail?
- What is the difference between IKO pro Stop Groene Aanslag and IKOpro Roof & Wall Cleaner?
- What is the difference between one-component and two-component liquid waterproofing?
- What is the fire resistance of an IKO enertherm PIR insulation board?
- What is the importance of a wind uplift test (wind box test)?
- What is the Indoor Climate Class of My Building?
- What is the lifespan/expectation of an IKO bituminous roofing membrane, and how can it be extended?
- What is thermal phase shift and how does IKO enertherm perform?
- What load can IKO enertherm PIR insulation withstand?
- What product can I use to maintain my IKO roof?
- What role do green roofs and water retention roofs play in climate change?
- What role does a mineral finish (slate/granulate) play on a bituminous membrane?
- What types of waterproofing systems can be used on IKO Enertherm PIR insulation?
- When and How to Maintain a Flat Roof?
- Which IKO enertherm PIR insulation board sizes can be bonded to a flat roof?
- Which paint can be used to paint over IKO hybritech MS Detail?
- Which PIR insulation can be used in façades in compliance with fire regulations?
- Which PIR insulation is used for installing a compact roof (warm bitumen)?
- Which primer should be used with IKO bituminous roofing membranes?
- Which PU adhesive is best used with IKO Enertherm PIR insulation?
- Why and when do we apply titanium dioxide on roofing membranes?
- Why are bitumen roofing membranes the ideal material for a circular flat roof?
- Why can zinc and lead be corroded by non-mineralized bituminous roofing membranes?
- Why Conduct a Wind Load Calculation for a Project?
- Why does IKO only recommend SBS bituminous membranes for single-layer mechanically fastened top layer systems?
- Why does IKO recommend liquid waterproofing for sealing complex roof details?
- Why does IKO recommend not finishing the overlaps of a bituminous roofing membrane with a trowel?
- Why is a vapor pressure–distributing underlayer applied in a two-layer bituminous system on IKO Enertherm PIR insulation?
- Why is the retrieval of Atelia bituminous roofing membranes from roofs only possible after 35 years?
- Why should upstands and flat roof areas be executed separately?
- Why use insulation compartmentalisation and how to apply it?